Waterless Trap Seals for Every Drain Size. Free Shipping Over $100 AUD
Green Drain GD 3-3.5 inch EG waterless trap seal with extended gasket for Australian floor drains
Main
Cross
Section
Exploded
APAC Exclusive GD 3-3.5" EG

3-3.5" EG Waterless Trap Seal

Extended gasket design bridges 3" to 3.5" drain openings for maximum compatibility across Australian plumbing systems. WaterMark certified.

$57.15 AUD

Inc. GST. Free shipping on orders over $100 AUD. $10 flat rate standard shipping.

Pipe Size 3-3.5" (DN 75-90mm)
Flow Rate 105.70 L/min
Install Time 30 Seconds
WaterMark Certified
ASSE 1072 Tested
Free Shipping Over $100

How it works.

Four flexible silicone sealing ribs form a one-way valve. Water and debris pass through under gravity. Commercial wash-down volumes, mop water, and kitchen runoff all drain normally.

When flow stops, the ribs close to create a continuous mechanical seal that blocks sewer gas, odours, and pests from entering the occupied space above.

The GD 3-3.5" EG features an extended gasket that accommodates pipe diameters from 75 to 90mm, bridging the gap between standard 3" and 3.5" drain openings common in Australian plumbing systems.

Green Drain cross-section diagram showing one-way valve open during flow and closed to block sewer gas and pests

ASSE 1072 tested. The data that matters.

The GD 3-3.5" EG is tested to ASSE 1072-2020, the North American performance standard for barrier-type floor drain trap seal devices. WaterMark certified for the Australian market.

105.70 L/min Flow Rate (Level U) No restriction to commercial drainage.
32g Opening Force Approx 4 oz. Opens under minimal water weight.
2,500+ Cycle Endurance ASSE 1072 tested open/close cycles.
>96% Evaporation Reduction Keeps trap seal intact without water priming.

Technical Specifications

ModelGD 3-3.5" EG
Pipe Size3-3.5" (75-90mm) / DN 80-90
Height50 mm
Housing MaterialABS Plastic
Valve MaterialSilicone Rubber
Seal MaterialSilicone Gasket (Extended)
Flow Rate105.70 L/min
ASSE 1072 Opening Force32 grams
ASSE 1072 Cycle Life>2,500 cycles
ASSE 1072 Evaporation Reduction>96%
WaterMark LicenseWM-022837 (DN80)
PatentsMultiple US & international patents

Installs in 30 seconds. No tools.

1
Step 1: Remove the drain grate

Remove the drain grate

Lift the existing drain grate or strainer from the floor drain body.

2
Step 2: Drop in the Green Drain

Drop in the GD 3-3.5" EG

Place the Green Drain into the drain body or hub opening. The extended gasket accommodates 75 to 90mm pipe diameters.

3
Step 3: Press gently to seat

Press gently to seat

Recess 2 to 4 inches below the pipe top. The extended silicone gasket creates a snug seal against the pipe walls.

4
Step 4: Replace the drain grate

Replace the grate

Put the grate back. Done. A full commercial floor in an afternoon.

Where the GD 3-3.5" EG is used.

The extended gasket design provides maximum compatibility across Australian commercial plumbing systems, from healthcare facilities to commercial kitchens.

Certifications and compliance.

Green Drain WaterMark Australia certification WM-022837

WaterMark Australia

WM-022837 (DN80)

Green Drain ASSE 1072-2020 barrier-type trap seal certification

ASSE 1072-2020

Trap seal performance standard

Green Drain CE Mark European Technical Assessment ETA-18/0536

CE / ETA-18/0536

European Technical Assessment

Green Drain NSF/ANSI 2 food equipment certification

NSF/ANSI 2

Food Equipment Certified

Green Drain HACCP International food safety endorsement

HACCP International

Certificate RG-04

Green Drain tested by Danish Technological Institute DTI

DTI Tested

Rapport 957187

SGS

SGS Pathogen Test

>99.9% blockage of viral aerosols

What operators are saying.

"After installing your product in all our floor drains, we could see a noticeable difference in the reduction of fruit fly and mosquito activity. We were also very impressed that the flow rate of our trough drain remained consistent."

Mike Malone, Owner and Head Brewer

Walking Tree Brewery

"I am impressed with the simplistic design and the quality of the materials of construction. Just with the pest issue resolved alone we are sold."

Fred Wilson, Product Specialist

Sysco Central Florida

For specifiers and engineers.

The GD 3-3.5" EG is WaterMark certified (WM-022837) for use in Australian plumbing installations. It meets the requirements of AS/NZS 3500 when installed as a supplementary trap seal device in floor drains.

Tested to ASSE 1072-2020 for flow rate, opening force, cycle endurance, and evaporation reduction. Compatible with DN 80 and DN 90 pipe sizes commonly found in Australian commercial buildings.

Specify the GD 3-3.5" EG for projects requiring WaterMark compliance and broad pipe diameter compatibility. Request spec sheets or schedule a consultation with our technical team.

Specifier Resources
Technical drawing
or spec sheet preview
~500x400px

Ready to protect your drains?

Drop-in install. No tools. Works from day one.