Waterless Trap Seals for Australian Drain Sizes. Free Shipping Over $100 AUD
Green Drain GD4 waterless trap seal for 4-inch floor drains
Main
GD4

4" Waterless Trap Seal

The most common commercial floor drain size. ≥340 L/min flow capacity. Drop-in install, no tools required.

$59.70 AUD

Inc. GST. Free shipping on orders over $100 AUD. $10 flat rate standard shipping.

Pipe Size 4" (102-110mm)
Flow Rate ≥340 L/min
Install Time 30 Seconds
WaterMark Certified
ASSE 1072 Tested
Free Shipping Over $100

How it works.

Four flexible silicone sealing ribs form a one-way valve. Water passes through under gravity. Even high-volume wash-down flows move through without restriction.

When flow stops, the ribs close to create a continuous mechanical seal that blocks sewer gas, odours, and pests from entering the occupied space above.

The valve opens under the weight of just 32 grams, approximately 4 oz of water. The flexible design accommodates pipe diameters from 102 to 110 mm.

Green Drain cross-section diagram showing one-way valve open during flow and closed to block sewer gas and pests

ASSE 1072-2020 Performance Data

Independently tested by IAPMO R&T. These are lab-verified results from an accredited third-party testing laboratory.

≥340 L/min Flow Rate (Level U) No restriction to drainage.
32g Opening Force Opens with approximately 4 oz of water.
2,500+ Cycle Endurance Open/close cycles tested and passed.
>96% Evaporation Reduction Maintains trap seal without water.

Technical Specifications

ModelGD4
Pipe Size4" (102-110 mm) / DN100
Height51 mm
Housing Diameter (no gasket)88.39 mm (3.480"), bottom 93.47 mm (3.680")
Housing with Gasket108.56 mm (3.274") wide x 50.7 mm (1.996")
Housing MaterialABS Plastic
Valve MaterialSilicone Rubber
Seal MaterialSilicone Gasket
Flow Rate≥340.00 L/min
ASSE 1072 Opening Force32 grams
ASSE 1072 Cycle Life>2,500 cycles
ASSE 1072 Evaporation Reduction>96%
Pressure Resistance (DTI)>400 Pa
WaterMark LicenseWM-022837 (DN100)
PatentsMultiple US & international patents

Installs in 30 seconds. No tools.

1
Step 1: Remove the drain grate

Remove the drain grate

Lift the existing drain grate or strainer from the floor drain body.

2
Step 2: Drop in the Green Drain

Drop in the GD4

Place the Green Drain into the drain body or hub opening.

3
Step 3: Press gently to seat

Press gently to seat

Recess 2 to 4 inches below the pipe top. The silicone gasket creates a snug seal against the pipe walls.

4
Step 4: Replace the drain grate

Replace the grate

Put the grate back. Done. A full commercial floor in an afternoon.

Where the GD4 is used.

The 4" floor drain is the most commonly specified drain size in new commercial construction. The GD4 appears in virtually every commercial vertical.

Certifications and compliance.

Green Drain WaterMark Australia certification WM-022837

WaterMark Australia

WM-022837 (DN100)

Green Drain ASSE 1072-2020 barrier-type trap seal certification

ASSE 1072-2020

Trap seal performance standard

Green Drain NSF/ANSI 2 food equipment certification

NSF/ANSI 2

Food Equipment Certified

Green Drain HACCP International food safety endorsement

HACCP International

Certificate RG-04

Green Drain CE Mark European Technical Assessment ETA-18/0536

CE / ETA-18/0536

European Technical Assessment

SGS

SGS Pathogen Test

>99.9% blockage of viral aerosols

Green Drain tested by Danish Technological Institute DTI

DTI Tested

Rapport 957187

Green Drain IAPMO R&T certified plumbing product

IAPMO R&T

Certified Testing Lab

Ready to protect your drains?

Drop-in install. No tools. Works from day one.